Resources

Guide · 6 November 2026 · 5 min read

Time of day tariff for industries: how ToD changes your bill

Since April 2024, industrial consumers in India pay at least 1.2 times the normal rate in peak hours and at least 20% less in solar hours. Here is how ToD shows up on your bill and which loads are worth moving.

A time of day (ToD) tariff charges a different rate for the same unit depending on when you use it: more in peak hours, less in solar hours. For industrial consumers in India it has applied since 1 April 2024, so moving the right loads out of peak hours is now one of the cheapest ways to cut an electricity bill.

What the 2023 rules say

The Ministry of Power notified the Electricity (Rights of Consumers) Amendment Rules on 14 June 2023. They added a rule on ToD tariffs that every state commission has to follow when it sets tariffs.

The main points for a plant head are these. ToD applies to commercial and industrial consumers with a maximum demand above 10 kW, from a date no later than 1 April 2024. The peak-hour rate for these consumers must be at least 1.2 times the normal rate. The rate in solar hours must be at least 20 per cent below the normal rate. Solar hours are eight hours a day, set by your state commission, and peak hours cannot be longer than solar hours. ToD applies to the energy charge, not to demand charges.

Each state commission sets its own hours and rates within these limits, so the peak block in one state may start at a different hour from the next. Some states are still aligning their tariff orders with the rules. The current tariff order for your DISCOM is the document that decides what you actually pay.

How ToD shows up on your bill

On an HT bill, ToD usually appears as units split into time blocks, with a surcharge on peak units and a rebate on off-peak or solar-hour units. The labels vary from DISCOM to DISCOM: ToD charges, peak surcharge, night or solar rebate. The total energy charge is the sum of each block's units at its own rate.

This is why two plants using the same units in a month can pay different energy charges. The plant that runs its furnace in the evening peak pays more for the same work than the plant that runs it at noon.

Illustrative example: say your normal energy rate is ₹7.00 per kWh. Under the minimums in the rules, the peak rate would be at least ₹8.40 and the solar-hour rate at most ₹5.60. A 100 kW load running for two hours uses 200 kWh. In the peak block that costs at least ₹1,680; in solar hours, at most ₹1,120. That is a gap of ₹560 or more for every day the load moves. Your own rates will differ; this example only applies the minimum ratios in the rules.

Which loads can move

Not every load can move. A continuous process line, or a cold store holding stock, has to run when it has to run. The loads worth looking at first are the ones that run in batches or that can store their output.

Common examples are furnaces and ovens that heat a batch, where the start time can sometimes shift; pumping water into an overhead tank; compressed air topping up receivers; chillers pre-cooling before a peak block, where the process allows it; charging forklifts and other batteries; and non-urgent grinding, crushing or mixing.

Each of these needs a check with production. Moving a furnace start by an hour is only a saving if the shift plan, labour and quality all still work.

How to find your peak-hour load

To act on ToD you need to know which machines run in the peak block. The monthly bill only gives units per block for the whole plant, not per machine.

There are three ways to get there. Read the load profile from your incomer meter, if your DISCOM or meter allows it, to see the shape of your day block by block. Add sub-meters or clamp-on CTs on the larger feeders and machines. Or connect the meters, SCADA or BMS data you already have to an energy monitoring system that splits consumption by tariff block for you.

Ardra EMS does the last of these. Its time-of-day view splits each feeder's consumption by tariff block, so you can see which loads could move. If you would rather have an engineer read a year of bills first, an energy audit ranks the fixes by rupee value.

ToD and maximum demand are different charges

Moving load out of peak hours lowers the energy charge. It does not by itself lower the demand charge, which depends on the highest demand recorded in the month. If you move several loads into the same solar-hour block, you can create a new demand peak and pay for it in demand charges instead. Plan the move with both charges in view.

A simple rule: spread shifted loads across the cheaper blocks rather than stacking them at the start of one.

Frequently asked questions

Does ToD apply to LT industrial consumers?

The 2023 rules cover commercial and industrial consumers with a maximum demand above 10 kW. How and from when your state applies it, and whether it needs a smart or ToD meter, is set in your DISCOM's tariff order.

Does the ToD rebate reduce demand charges?

No. ToD applies to the energy charge only. Demand charges are worked out separately, from your recorded maximum demand and contract demand.

Where do I find my state's peak and solar hours?

In the current tariff order from your State Electricity Regulatory Commission, which is usually also published on your DISCOM's website.

Want to see your own peak-hour units? Upload a bill to the instant AI bill check on the home page, or request a demo and an engineer will go through one month's bill with you.

Keep reading

Want this read on your own bill?

Request a demo
Request a demo